The kw hls (hydraulic lift system) provides additional road clearance for lowered vehicles. When expanded, a range of 30mm to 45mm of lift is produced, thereby helping sport cars avoid road clearance difficulties like speed bumps, road constructions etc.

version hls 4: covers both the front and rear axles of the vehicle.

Features:
- for vehicles with with little road clearance
- vehicle specific applications
- activation of change in height by a small keychain transmitter avoiding the need to run additional wires through the vehicle
- height changes can be done while the vehicle is moving, up to speeds of 50 mph
- automatically lowering of the vehicle
- with tv certificate
- rub...(choose a part on the right to read more)

General Fitment

This 9 inch front and 11 inch rear steel fender flare set is made in Germany, we offer a complete line of replacement bodywork to complement the entire Porsche model range. Sold individually. 1 necessary per car. Please note: for conversions, these flares will allow you to run 9 wide tires in the front and 11 wide in the rear. For the 964 / 965 models the torsion bar cut out must be filled. Due to variances in production at the factory, age, accident damage or rust, each part may require trimming and or adjustment for perfect fitment.

This item may need to be sourced from Germany and would take 2-4 weeks to arrive. Once ordered it cannot be canceled. Please call to check stock or request expedited shipping.

Lagerspuren

This item may need to be sourced from Germany and would take 2-4 weeks to arrive. Once ordered it cannot be canceled. Please call to check stock or request expedited shipping.

Allows you to convert to one fan belt to run the fan and alternator like the factory rs versions. Oem part sourced in Germany to ensure quality, reliability and precise fitment. Once installed the alternator will run at the fan speed. That will lessen the inertial load and will add slightly more horsepower and acceleration. - includes fasteners (3 qty. M 6x35) - weighs .4 lbs ( .17 kg) please note: for 993 race car conversions or for cars without a/c we also recommend the corresponding crankshaft pulley, part # 99310205040 sold individually. 1 necessary per car.

This item may need to be sourced from Germany and would take 2-4 weeks to arrive. Once ordered it cannot be canceled. Please call to check stock or ...(choose a part on the right to read more)

Written by Dr. 914, this guide tells you what you are getting yourself into when converting your four cylinder to a six. It also offers engine and suspension recommendations as well as wiring guides, parts lists and templates. A must for the six conversion.

General Fitment

Porsche 911 ac compressor upgrade kit, 1984-89, lh drive model provides improved integrity with our kuehl barrier hose set, kuehl low- high pressure switch to help protect the system, a new denso factory compressor with clutch, new kuehl drier, complete o-ring kit, along with r134a charge port adapters. you can use either r12 or r134a with refrigerant with this complete kit. all barrier hoses match OEM configuration, have sae sae approved crimped fittings and each hose is labeled so you know where it goes.

Fits these applications

lh drive models
Porsche 911 non-turbo, 1984-1989 (pre 964 model)
coupe, cabriolets, and turbo look bodies.
with factory installed ac

Includes

new...(choose a part on the right to read more)

Sold as a set. 1 necessary per car.

This item may need to be sourced from Germany and would take 2-4 weeks to arrive. Once ordered it cannot be canceled. Please call to check stock or request expedited shipping.

This kit convert's the 997 turbo pccb rotors to steel rotors with yellow pagid pads.( only 5-hole, not central lock ) this system is complete with everything that you need to install. Do not ruin your expensive ceramic brake discs on the track. Get ready for racing with the original and much cheaper Porsche motorsport steel brake discs! What's in the box: 4 x 2-piece brake discs (380 x 34 mm - front / 350 x 28 mm - rear) 4 x wear sensors 2 x set ( front and rear ) brake pad set (pagid yellow - rs29 ) 8 x screws for brake caliper 8 x damping plates technical tip: also order stainless steel brake lines (FVD b96 355 97) and racebrake fluid (012 145 ca).

This item may need to be sourced from Germany and would ...(choose a part on the right to read more)

Our k24 sport turbocharger is based off the optional k24 turbochargers, found in the GT2 or 993 turbo x50 models. They are remanufactured by borg warner certified technicians in Germany and are a cost-effective solution. The remanufacturing process includes full inspection of the turbocharger to ensure proper operation after the remanufacturing process. We then disassemble, clean and degrease the unit. The compressor wheels are exchanged, lightened and modified for more air flow. All clearances / shaft tolerances are checked for precision to ensure reliability. The end result is 20-30 additional horsepower, in the low and mid rpm range over the factory turbo. The sport turbo also has less lag than a factory k24...(choose a part on the right to read more)

Sold as a set. 1 necessary per car.

This item may need to be sourced from Germany and would take 2-4 weeks to arrive. Once ordered it cannot be canceled. Please call to check stock or request expedited shipping.

The bbi autosport Porsche 996/997 turbo clutch slave cylinder conversion kit is a direct replacement part that eliminates the problematic factory power-assist system for improved reliability and pedal feedback. The factory power-assisted clutch system has always been the achilles heel for the Porsche 997 turbo. Utilizing the power steering system to help reduce the force needed to depress the clutch pedal, it is a flawed design that delivers a mushy pedal feel with poor feedback, and is highly prone to failure.

Unlike other kits, the bbi autosport kit is designed be used with OEM clutch master cylinder, hose, and spring pack. This eliminates the need for additional parts, making our kit a complete plug an...(choose a part on the right to read more)

Nur wenn mit pccb ( keramik bremse ) ausgeliefert wurde.

This item may need to be sourced from Germany and would take 2-4 weeks to arrive. Once ordered it cannot be canceled. Please call to check stock or request expedited shipping.

Our k24 sport turbocharger is based off the optional k24 turbochargers, found in the GT2 or 993 turbo x50 models. They are remanufactured by borg warner certified technicians in Germany and are a cost-effective solution. The remanufacturing process includes full inspection of the turbocharger to ensure proper operation after the remanufacturing process. We then disassemble, clean and degrease the unit. The compressor wheels are exchanged, lightened and modified for more air flow. All clearances / shaft tolerances are checked for precision to ensure reliability. The end result is 20-30 additional horsepower, in the low and mid rpm range over the factory turbo. The sport turbo also has less lag than a factory k24...(choose a part on the right to read more)

This kit convert's the 997 turbo GT2's / 997gt3 rs pccb rotors to 997 GT3 cup car steel rotors with green cup car pads ( for cars with central lock only ) this system is complete with everything that you need to install. Do not ruin your expensive ceramic brake discs on the track. Get ready for racing with the original and much cheaper Porsche motorsport steel brake discs! What's in the box: 4 x 2-piece brake discs (380 x 34 mm - front / 350 x 28 mm - rear) 4 x wear sensors 8 x cup brake pads (racing green) 8 x screws for brake caliper 8 x damping plates technical tip: also order stainless steel brake lines (FVD b96 355 97) and racebrake fluid (012 145 ca).

This item may need to be sourced from Germany an...(choose a part on the right to read more)

This item may need to be sourced from Germany and would take 2-4 weeks to arrive. Once ordered it cannot be canceled. Please call to check stock or request expedited shipping.

This item may need to be sourced from Germany and would take 2-4 weeks to arrive. Once ordered it cannot be canceled. Please call to check stock or request expedited shipping.

Center locking conversion kit central locking device for fast wheel changes on the racetrack. Kit includes: - center locking system - removal key and hardware - brake disk connecting parts for centerlock tech info: you need central locking wheels ! Professional installation required.

This item may need to be sourced from Germany and would take 2-4 weeks to arrive. Once ordered it cannot be canceled. Please call to check stock or request expedited shipping.

Enjoy the European brighter light for your 944! Euro h4 conversion kit for all 944.

This item may need to be sourced from Germany and would take 2-4 weeks to arrive. Once ordered it cannot be canceled. Please call to check stock or request expedited shipping.

Adapts up to 3 2l into 914 914-4 chassis 1970-1976

Increase your safety and visibility with this hlv7 series 9006 led headlight/fog light kit. The single-beam led headlight bulbs emit 4,000 lumens of cool white illumination per set (2,000 lumens each) and feature 3rd generation cooling technology. They have integrated heat sinks instead of short-lived fans or bulky braided heat sinks. This allows for a longer-lasting bulb and easier installation in tight spaces. They also have internal drivers, which eliminates the need to mount an additional part and locate an appropriate mounting spot. The bulbs last 13 times longer than halogen bulbs. Led arrays in each bulb are designed to mimic the filament in halogen bulbs—creating a closely matched beam style. These ca...(choose a part on the right to read more)

General Fitment

This is a custom system made for a 997.1 GT3 cup with a 4.0 l conversion that has 500 hp+ - header diameter 55mm - tube diameter 76mm after the headers - recommended for engines 500 hp+ all motorsport and racing parts are special order items. Special order items must be paid for in advance. Special order items are sold on a non-cancelable, non-exchangeable, non-returnable, non-refundable basis and do not carry any warranty. No exceptions.

This item may need to be sourced from Germany and would take 2-4 weeks to arrive. Once ordered it cannot be canceled. Please call to check stock or request expedited shipping.

If you have a us model 1980-83 911 SC and are looking to replace your heat exchangers we have some good and bad news. The original heat exchangers (part # 930 211 025 02) are no longer available from Porsche. But, these stainless-steel industries (ssi) heat exchangers will work with modifications. The good news is, once done, you will have more torque and horsepower! Free flow conversion heat exchangers improve sound and performance, while reducing backpressure and thermal load on the motor. These are based off the early style exhausts found on the 1974 2.7 l rs. Those models had a straight through, superior, free flow exhaust design that included a dual inlet muffler. When converting to these heat exchangers y...(choose a part on the right to read more)

This kit convert's the 997 turbo pccb rotors to steel rotors with yellow pagid pads.( only 5-hole, not central lock ) this system is complete with everything that you need to install. Do not ruin your expensive ceramic brake discs on the track. Get ready for racing with the original and much cheaper Porsche motorsport steel brake discs! What's in the box: 4 x 2-piece brake discs (380 x 34 mm - front / 350 x 28 mm - rear) 4 x wear sensors 2 x set ( front and rear ) brake pad set (pagid yellow - rs29 ) 8 x screws for brake caliper 8 x damping plates technical tip: also order stainless steel brake lines (FVD b96 355 97) and racebrake fluid (012 145 ca).

This item may need to be sourced from Germany and would ...(choose a part on the right to read more)